{"id":12810,"date":"2021-03-20T11:59:42","date_gmt":"2021-03-20T11:59:42","guid":{"rendered":"https:\/\/www.obd2tool.com\/blog\/?p=12810"},"modified":"2021-03-20T12:02:38","modified_gmt":"2021-03-20T12:02:38","slug":"chrysler-town-2012-used-pcm-reprogramming-by-autel-im608-programmer","status":"publish","type":"post","link":"https:\/\/www.obd2tool.com\/blog\/chrysler-town-2012-used-pcm-reprogramming-by-autel-im608-programmer\/","title":{"rendered":"Chrysler Town 2012 Used PCM Reprogramming by Autel IM608 Programmer"},"content":{"rendered":"

This post show you guide on how to use Autel IM608 programmer<\/a> to do used PCM reprogramming for Chrysler Town 2012.More case about Chrysler,please check here Chrysler trouble repair<\/a>.<\/p>\n

Note:<\/strong> If you want to get a lower price for Autel Scanner<\/a>, please contact our email: sales@obd2tool.com<\/a><\/span><\/p>\n

\"\"<\/p>\n

When a PCM is replaced,please make sure the used module has same part number as the original module.If used module comes with black key,it is a security key.If it\u2019s a grey key,it is not security.<\/p>\n

Secret Key is an ID code that is unique to each WIN.This code is programmed and stored in the WIN,the PCM,and each ignition key transponder chip.When the PCM or WIN is replaced,it is necessary to program the Secret Key code into the new module.<\/p>\n

Pin Code\u2013A 4 digit PIN is required to enter the Security Access Mode of the WCM\/WIN (aftermarket tolls will produce a 5 digit)<\/p>\n

Chrysler IMMO System:<\/strong><\/p>\n

SKIM\/WCM<\/p>\n

Sentry Key immo module 1998-2006<\/p>\n

SKREEM\/WCM<\/p>\n

Sentry key remote entry module\/wireless control module 2004-2014<\/p>\n

WIN<\/strong><\/p>\n

Wireless ignition node 2008-present<\/p>\n

Keyless Go<\/strong><\/p>\n

Keyless Go 2008-2016<\/p>\n

Smart Start<\/strong><\/p>\n

Push button non WIN module 2011-present<\/p>\n

Procedures:<\/strong><\/p>\n

Disconnect and isolate the negative battery cable<\/p>\n

Read and support the vehicle (refer to 04-vehicle reference hosting-standard procedure)<\/p>\n

Remove the push pin (2) and reposition the PCM access cover<\/p>\n

\"\"<\/p>\n

Unlock and disconnect the electrical connectors from the Powertrain Control Module<\/p>\n

\"\"<\/p>\n

Remove the three bolts and PCM<\/p>\n

\"\"<\/p>\n

Connect Autel IM608 to Chrysler Town<\/p>\n

Select \u201cIMMO\u201d\u2013>\u201dChrysler\u201d\u2013>\u201dAutomatic Selection\u201d<\/p>\n

Turn ignition,then press \u201cOK\u201d to continue<\/p>\n

Select \u201cFobik Key\u201d<\/p>\n

\"\"<\/p>\n

Switch the ignition off and then on again,make sure the engine is off,then press \u201cOK\u201d<\/p>\n

Now it show you with password:8509<\/p>\n

\"\"<\/p>\n

Press \u201cOK\u201d,then click \u201cimmo status scan\u201d<\/p>\n

\"\"<\/p>\n

Press \u201cReplace component\u201d<\/p>\n

\"\"<\/p>\n

Press \u201cPowertrain control module (PCM) replaced\u201d<\/p>\n

\"\"<\/p>\n

It will show you with some prompt message,just press \u201cOK\u201d to continue<\/p>\n

Click \u201cOK\u201d to continue<\/p>\n

\"\"<\/p>\n

VIN write to the powertrain control module (PCM) was successful.<\/p>\n

Click \u201cOK\u201d to continue<\/p>\n

\"\"<\/p>\n

Now back and click \u201cRescan\u201d<\/p>\n

\"\"<\/p>\n

Click on \u201cTrouble codes (WCM)\u201d<\/p>\n

\"\"<\/p>\n

Then clear the DTC,then ESC<\/p>\n

After then back to Autel IM608 main menu to select \u201cDiagnostics\u201d<\/p>\n

Then click \u201cVIN\u201d icon,select \u201cAuto Scan\u201d<\/p>\n

\"\"<\/p>\n

And select \u201cChrysler USA\u201d<\/p>\n

\"\"<\/p>\n

Vehicle identification<\/p>\n

\"\"<\/p>\n

Click \u201cDiagnosis\u201d\u2013>\u201dControl unit\u201d\u2013>\u201dBody\u201d<\/p>\n

Select \u201cWCM\/TPMS (Wireless Control)\u201d<\/p>\n

Select \u201cSpecial Function\u201d<\/p>\n

\"\"<\/p>\n

Select \u201cReset ECU\u201d<\/p>\n

ECU has been reset<\/p>\n

\"\"<\/p>\n

If the system has a fault code,cycle the ignition and clear the fault code.<\/p>\n","protected":false},"excerpt":{"rendered":"

This post show you guide on how to use Autel IM608 programmer to do used PCM reprogramming for Chrysler Town<\/p>\n","protected":false},"author":1,"featured_media":12828,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[98,11,2304],"tags":[1513,1655,1654,1512,2174,1656,1612,365,1609],"views":2873,"_links":{"self":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/12810"}],"collection":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/comments?post=12810"}],"version-history":[{"count":4,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/12810\/revisions"}],"predecessor-version":[{"id":12832,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/12810\/revisions\/12832"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/media\/12828"}],"wp:attachment":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/media?parent=12810"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/categories?post=12810"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/tags?post=12810"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}