{"id":6409,"date":"2019-08-08T08:26:16","date_gmt":"2019-08-08T08:26:16","guid":{"rendered":"http:\/\/www.obd2tool.com\/blog\/?p=6409"},"modified":"2019-08-08T09:12:25","modified_gmt":"2019-08-08T09:12:25","slug":"how-to-use-fvdi-2018-to-change-golf-6-2012-dash","status":"publish","type":"post","link":"https:\/\/www.obd2tool.com\/blog\/how-to-use-fvdi-2018-to-change-golf-6-2012-dash\/","title":{"rendered":"How to use FVDI 2018 to change Golf 6 2012 dash"},"content":{"rendered":"

How to change dash to Golf 6 2012\u00a0by FVDI 2018<\/a>? Here is the step-by-step guide with you.<\/p>\n

 <\/p>\n

Prepare:<\/b><\/strong><\/p>\n

Golf 6 2012\u00a0dash<\/p>\n

FVDI V2018 ABRITES Commander<\/p>\n

Connection adapter<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-1\"<\/a><\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-2\"<\/a>\u00a0\"fvdi-2018-change-golf-6-2012-dash-3\"<\/a><\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-4\"<\/a><\/p>\n

Procedures<\/b><\/strong>:<\/b><\/strong><\/p>\n

Connect adapter to dash and active Immobilizer<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-5\"<\/a><\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-6\"<\/a><\/p>\n

Open \u201cFVDI and AVDI and VVDI V2018 Quick Loader V3.0\u201d\u00a0software<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-7-1024x531\"<\/a><\/p>\n

Select V24.0<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-8-1024x526\"<\/a><\/p>\n

Connect to the interface success<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-9-1024x518\"<\/a><\/p>\n

Attention:<\/p>\n

Please check whether internet connection is available in order to perform hardware synchronization.<\/p>\n

IF the hardware is not synchronized in the next o hours, it will be not able to communicate with the vehicles.<\/p>\n

Please confirm that you have read and understood this warning.<\/p>\n

Click \u201cOK\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-10-1024x532\"<\/a><\/p>\n

Checking for programmer, please wait\u2026<\/p>\n

There is no programmer currently connected<\/p>\n

Select \u201cDash Board\u201d-> \u201cDiagnostic channel is open\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-11-1024x521\"<\/a><\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-12-1024x522\"<\/a><\/p>\n

Show the device information below<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-13-1024x522\"<\/a><\/p>\n

Return to Dash board page<\/p>\n

Click \u201cSpecial function\u201d-> \u201cCAN Instrument\u201d-> \u201cEnter Service Mode by OBDII\u201d<\/p>\n

Note: Cannot enter bootloader. Make sure you give ignition ON with working key!<\/p>\n

If the car doesn\u2019t have any working key, you should enter service mode using a programmer<\/p>\n

And then click \u201cOK\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-14-1024x530\"<\/a><\/p>\n

Exit the software<\/p>\n

Take out the adapter<\/p>\n

Remove the dash cover<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-15\"<\/a><\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-16\"<\/a><\/p>\n

Open \u201cCARPROG v08.21\u201d software<\/p>\n

Select \u201cEEPROM\u201d-> \u201c93C, 24C, 95X V2.6\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-17-1024x530\"<\/a><\/p>\n

Click tool logo, select \u201c24C\u201d-> \u201c24C32\u201d<\/p>\n

And then click \u201cOK\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-18-1024x527\"<\/a><\/p>\n

Click the init logo<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-19-1024x531\"<\/a><\/p>\n

Select the relevant logo to save \u201cgolf6-2012 original.bin\u201d file<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-20-1024x527\"<\/a><\/p>\n

Exit the software<\/p>\n

Open ABRITES Diagnostics for VW\/AUDI\/ SEAT\/SKODA 24.0 software<\/p>\n

Run the software<\/p>\n

Select \u201cLoad ConfData (24C32\/24C64) dump<\/p>\n

Open \u201cgolf6-2012 original.bin\u201d file saved just now<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-21-1024x520\"<\/a><\/p>\n

Select \u201cEnter Service mode by ConfData dump (24C32\/24C64)<\/p>\n

Save file name as \u201cgolf 2102 service mode\u201d<\/p>\n

Exit\u2026<\/p>\n

Go to CARPROG v08.21 software-> \u201cEEPROM\u201d-> \u201c93C, 24C, 95X V2.6\u201d<\/p>\n

Click tool logo, select \u201c24C\u201d-> \u201c24C32\u201d, click \u201cOK\u201d<\/p>\n

Open the file \u201cgolf 2102 service mode\u201d saved above<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-22-1024x526\"<\/a><\/p>\n

Click here to write data<\/p>\n

Verify OK<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-23-1024x525\"<\/a><\/p>\n

Exit CARPROG v08.21 software<\/p>\n

Open \u201cABRITES Diagnostics for VW\/AUDI\/ SEAT\/SKODA 24.0\u201d software<\/p>\n

Select \u201cEnter Service mode by OBD II\u201d<\/p>\n

Click \u201cRead mileage\u201d<\/p>\n

Change the mileage<\/p>\n

Click \u201cRead ConfData\u201d<\/p>\n

Then click \u201cRead IMMO data\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-24-1024x527\"<\/a><\/p>\n

Change ID code and click \u201cUpdate IMMO data\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-25-1024x531\"<\/a><\/p>\n

Click \u201cErase All Keys\u201d and click \u201cYES\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-26-1024x532\"<\/a><\/p>\n

Click \u201cAdd key\u201d to program new key<\/p>\n

Note: Please insert new key\/ transponder into the key programmer.<\/p>\n

ATTENTION: After this operation transponder will be locked and cannot be used on other car. Do you want to continue?<\/p>\n

Click \u201cOK\u201d to continue<\/p>\n

 <\/p>\n

Choose position and click \u201cOK\u201d<\/p>\n

Click \u201cAdd key\u201d again to repeat all the steps above<\/p>\n

Transponder is written successfully<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-28-1024x539\"<\/a><\/p>\n

Click \u201cUpdate IMMO data\u201d to update<\/p>\n

Pay attention to the prompt \u201cThis will exit service mode. Further entering into service may require to\u00a0read\/write ConfData with a programmer. Do you want to continue?\u201d<\/p>\n

Click \u201cYES\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-29-1024x531\"<\/a><\/p>\n

Exit<\/p>\n

Go to \u201cABRITES Diagnostics for VW\/AUDI\/ SEAT\/SKODA 24.0\u201d software<\/p>\n

Click \u201cGuide Functions\u201d-> Instrument Cluster\u201d-> \u201cChange Language\u201d<\/p>\n

Click \u201cNext\u201d to choose language you need<\/p>\n

Return to \u201cInstrument Cluster\u201d, select \u201cSeatbelt warning activation\/deactivation\u201d<\/p>\n

Click \u201cNext\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-30-1024x526\"<\/a><\/p>\n

Select \u201cSeatbelt warning inactivation\/installed\u201d<\/p>\n

Note: This will change instrument cluster\u2019s coding. Do you want to continue?\u201d<\/p>\n

Click \u201cOK\u201d<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-31-1024x527\"<\/a><\/p>\n

Write new configuration\u2026<\/p>\n

Install odometer and test it successfully<\/p>\n

\"fvdi-2018-change-golf-6-2012-dash-32\"<\/a><\/p>\n

FVDI V2018\u00a0<\/b><\/strong>change Golf 6 2012 dash success!<\/p>\n

Done!<\/p>\n

 <\/p>\n","protected":false},"excerpt":{"rendered":"

How to change dash to Golf 6 2012\u00a0by FVDI 2018? Here is the step-by-step guide with you.   Prepare: Golf<\/p>\n","protected":false},"author":2,"featured_media":6410,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[613],"tags":[1481,616,1180,1225,613,1228],"views":3757,"_links":{"self":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/6409"}],"collection":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/comments?post=6409"}],"version-history":[{"count":4,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/6409\/revisions"}],"predecessor-version":[{"id":6455,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/posts\/6409\/revisions\/6455"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/media\/6410"}],"wp:attachment":[{"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/media?parent=6409"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/categories?post=6409"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.obd2tool.com\/blog\/wp-json\/wp\/v2\/tags?post=6409"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}