How to use FVDI 2018 to change Golf 6 2012 dash

How to change dash to Golf 6 2012 by FVDI 2018? Here is the step-by-step guide with you.

 

Prepare:

Golf 6 2012 dash

FVDI V2018 ABRITES Commander

Connection adapter

fvdi-2018-change-golf-6-2012-dash-1

fvdi-2018-change-golf-6-2012-dash-2 fvdi-2018-change-golf-6-2012-dash-3

fvdi-2018-change-golf-6-2012-dash-4

Procedures:

Connect adapter to dash and active Immobilizer

fvdi-2018-change-golf-6-2012-dash-5

fvdi-2018-change-golf-6-2012-dash-6

Open “FVDI and AVDI and VVDI V2018 Quick Loader V3.0” software

fvdi-2018-change-golf-6-2012-dash-7-1024x531

Select V24.0

fvdi-2018-change-golf-6-2012-dash-8-1024x526

Connect to the interface success

fvdi-2018-change-golf-6-2012-dash-9-1024x518

Attention:

Please check whether internet connection is available in order to perform hardware synchronization.

IF the hardware is not synchronized in the next o hours, it will be not able to communicate with the vehicles.

Please confirm that you have read and understood this warning.

Click “OK”

fvdi-2018-change-golf-6-2012-dash-10-1024x532

Checking for programmer, please wait…

There is no programmer currently connected

Select “Dash Board”-> “Diagnostic channel is open”

fvdi-2018-change-golf-6-2012-dash-11-1024x521

fvdi-2018-change-golf-6-2012-dash-12-1024x522

Show the device information below

fvdi-2018-change-golf-6-2012-dash-13-1024x522

Return to Dash board page

Click “Special function”-> “CAN Instrument”-> “Enter Service Mode by OBDII”

Note: Cannot enter bootloader. Make sure you give ignition ON with working key!

If the car doesn’t have any working key, you should enter service mode using a programmer

And then click “OK”

fvdi-2018-change-golf-6-2012-dash-14-1024x530

Exit the software

Take out the adapter

Remove the dash cover

fvdi-2018-change-golf-6-2012-dash-15

fvdi-2018-change-golf-6-2012-dash-16

Open “CARPROG v08.21” software

Select “EEPROM”-> “93C, 24C, 95X V2.6”

fvdi-2018-change-golf-6-2012-dash-17-1024x530

Click tool logo, select “24C”-> “24C32”

And then click “OK”

fvdi-2018-change-golf-6-2012-dash-18-1024x527

Click the init logo

fvdi-2018-change-golf-6-2012-dash-19-1024x531

Select the relevant logo to save “golf6-2012 original.bin” file

fvdi-2018-change-golf-6-2012-dash-20-1024x527

Exit the software

Open ABRITES Diagnostics for VW/AUDI/ SEAT/SKODA 24.0 software

Run the software

Select “Load ConfData (24C32/24C64) dump

Open “golf6-2012 original.bin” file saved just now

fvdi-2018-change-golf-6-2012-dash-21-1024x520

Select “Enter Service mode by ConfData dump (24C32/24C64)

Save file name as “golf 2102 service mode”

Exit…

Go to CARPROG v08.21 software-> “EEPROM”-> “93C, 24C, 95X V2.6”

Click tool logo, select “24C”-> “24C32”, click “OK”

Open the file “golf 2102 service mode” saved above

fvdi-2018-change-golf-6-2012-dash-22-1024x526

Click here to write data

Verify OK

fvdi-2018-change-golf-6-2012-dash-23-1024x525

Exit CARPROG v08.21 software

Open “ABRITES Diagnostics for VW/AUDI/ SEAT/SKODA 24.0” software

Select “Enter Service mode by OBD II”

Click “Read mileage”

Change the mileage

Click “Read ConfData”

Then click “Read IMMO data”

fvdi-2018-change-golf-6-2012-dash-24-1024x527

Change ID code and click “Update IMMO data”

fvdi-2018-change-golf-6-2012-dash-25-1024x531

Click “Erase All Keys” and click “YES”

fvdi-2018-change-golf-6-2012-dash-26-1024x532

Click “Add key” to program new key

Note: Please insert new key/ transponder into the key programmer.

ATTENTION: After this operation transponder will be locked and cannot be used on other car. Do you want to continue?

Click “OK” to continue

 

Choose position and click “OK”

Click “Add key” again to repeat all the steps above

Transponder is written successfully

fvdi-2018-change-golf-6-2012-dash-28-1024x539

Click “Update IMMO data” to update

Pay attention to the prompt “This will exit service mode. Further entering into service may require to read/write ConfData with a programmer. Do you want to continue?”

Click “YES”

fvdi-2018-change-golf-6-2012-dash-29-1024x531

Exit

Go to “ABRITES Diagnostics for VW/AUDI/ SEAT/SKODA 24.0” software

Click “Guide Functions”-> Instrument Cluster”-> “Change Language”

Click “Next” to choose language you need

Return to “Instrument Cluster”, select “Seatbelt warning activation/deactivation”

Click “Next”

fvdi-2018-change-golf-6-2012-dash-30-1024x526

Select “Seatbelt warning inactivation/installed”

Note: This will change instrument cluster’s coding. Do you want to continue?”

Click “OK”

fvdi-2018-change-golf-6-2012-dash-31-1024x527

Write new configuration…

Install odometer and test it successfully

fvdi-2018-change-golf-6-2012-dash-32

FVDI V2018 change Golf 6 2012 dash success!

Done!