Category Archives: Auto ecu programmer

Compare New Xprog M V6.12 with Old Xprog M V5.84 ECU Programmer

New Xprog V6.12 more functions than old version,New Generation Hardware, runs more steady and faster than old version.   Now, we’ll talk about the difference: 1.Items in parcel 2.PCB 3.Authorization   in detail.. 1.Xprog 5.84 and 6.12 full kit Note: Xprog 6.12 comes with 4 new adapters: ADP-0006 M35080 ICP, QFP64 MC908AZ/AS603K85K, ADP-0019 Rev. B, […]

Continue reading >

5139_P_1462420908155

How to Install OEM Orange 5 Programmer Software?

Note:For OEM Orange 5 programmer software,you do not need install software.Only install the Orange 5 programmer interface driver,then you can use software directly.   How to Install OEM Orange 5 Programmer software in XP system? Open the download folder,and click to open [software] folder Copy the “orange 5 v1.34” folder to desktop Connect OEM Orange 5 […]

Continue reading >

AT200

CGDI BMW AT-200 AT200 ECU Programmer has Updated to Newest Version

AT200 ECU Programmer Feather: 1.BMW AT-200 support BMW ECU Data reading, writing and clone, like MSV90 MSD85 MSD87 N2055 B38 B48 2.Support BMW IMMO functions, read BMW ISN Code by OBD. 3.Original from CGDI, Free update online.   CGDI BMW AT-200 released notes: 1.new: can read ISN for MSD80, MSD81 2.new: add wiring diagram TC1793, TC1793S 3.new: […]

Continue reading >

2467_P_1539330944965

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and […]

Continue reading >

xprog m

How to read & decode BMW CAS4 5M48H with XPROG-M Programmer?

This article shows the procedures on reading & decoding BMW CAS4 5M48H with XPROG-M Programmer.   Procedures: Remove BMW CAS4 module and get 5M48H controller from PCB Then weld it on the XPROG-M adpater Run XPROG software,and click [Device] button Select [Immobilizers]–>[CAS4 1N35H 5M48H…1030 v1]–>[1N35H_5M48H_D-FLASH_v1] Now click [Read] button The XPROG-M programmer indicate light will flash Progress… It […]

Continue reading >

AT200 ECU Programmer

2019.08 AT200 ECU programmer BMW Vehicle Coverage

AT200 BMW ECU programmer is updated to versio 1.31. It coveres 1272 new car models. And it can work for B38DME, to read ISN and clone ECU.   AT200 ECU programmer BMW car list: Series   Engine ECU 1 E82 116d 2000 N47D20 116 BOSCH EDC17C41 118d N47D20 143 BOSCH EDC17C41 120d N47D20 184 BOSCH EDC17C41 […]

Continue reading >

10027_P_1528165694179

How to Use XPROG Programmer V5.84 Reset BMW FRM3

In this instruction, obd2tool will show you guide on how to use XPROG programmer to reset BMW FRM3.     XPROG Programmer Reset BMW FRM3 Procedures: Remove BMW FRM module from vehicle,then disassemble cover. Open the diagram connection And follow above diagram to weld 3M25J adapter on FRM PCB   Connect XPROG programmer to PC […]

Continue reading >

主图

CN200 Super Programmer Supporting Airbag, ECU and Mileage

CN200 is a new universal programmer for ECU/MCU/BCM read & write, mileage correction and airbag reset etc.   CN200 Programmer Function List: MCU Read/Write:  8 pin chips, Atmel, Fujitsu , Infineon , Motorola, Renesas, ST mcus Airbag reset/repair Odometer correction: Benz, BMW, Volvo,Honda, Hyundai, Kia, Suzuki, Changan, etc ECU Read/Write: Benz, BMW, Audi,Porsche, Jaguar Land […]

Continue reading >

kess v2

Compare K-TAG FW 8.000 Master with Ktag FW 7.020 master

New Russian KTAG 8.000 master, 111 New protocols &313 Updated protocols, is 441usd-337usd more expensive than Ktag 7.020 master, also it has a different internal board. New Russian KTAG 8.000 master only works online ! with the Internet connected. 313 Updated protocols 111 New protocols https://mega.nz/#!QdpxDQRZ!d8ILWOxpgjnGqbO7txPbLqqHIbQVHoV2w33XmbdbjA0   Screenshot a part for sharing:   ktag fw 8000 […]

Continue reading >

How to Reset Benz ME9.7 ECU with CGDI Prog MB Benz?

This is the procedure on how to use CGDI Prog Benz Monster to reset/renew Benz ME9.7 ECU.   Procedures: Build wire connection between ME9.7 ECU,CGDI MB programmer and computer   Open CGDI Benz software,click “Wiring Diagram”,then select “ECU”à”ME9.7” to check the your connections are correctly.   Select “Auto Computer”,then click “Read”   After reading process completing,you […]

Continue reading >